T-MODE: In “T” mode, one sets the SHUTTER SPEED to a desired value and the ISO “floats” - which means it is adjusted automatically by the camera. You might use “T” mode if minimizing motion blur or stopping the action is a high priority for you. STEPS: 1. Choose auto ISO or set an ISO (see guidelines below) 2. Dial-in an exposure time 3. Shoot photo. Considerations for selecting exposure time (shutter speed): : Is there motion blur potential? if so, dial in a shorter time 1/250 or shorter ... 1/1000 : Is there a bright background problem? Setting the metering to "spot" forces camera to use that small zone to compute ISO Advantage of T Mode: While pressing shutter half-way down, you can adjust exposure time to get bird lit up enough to show detail in situations where the background is extremely bright (or dim). (This is essentially a shortcut to using "exposure compensation" in "P" or "A" modes) Potential disadvantage: Using "auto-ISO" allows the ISO to “float” as the camera selects an ISO value which will allow it to provide the shutter speed you have dialed in. With the Canon SX40 and SX50 electrical noise begins to show up by ISO 800 (or even lower if your subject is very small/ ie far away). Cameras with larger sensors tend to be able to go to higher ISO values without this problem. Auto-ISO: -----> On the one hand: you will get a photo, and more quickly -----> On the other hand: you may have more electrical noise than you need to have . (This would no issue if your subject is a landscape or anything which fills a large portion of the frame; but birds rarely take up much of the frame, so cropping becomes essential, and electrical noise quickly shows up in the bridge (medium to small sensor) cameras. One way to deal with this potential problem: Change from "auto-ISO" to a specific value. Considerations in selecting an ISO value: Is there a potential for "motion blur" problems: (birding flitting around, flying ... )? If so, set ISO higher, like 400, 800 … 1000 If lighting is bright, try ISO 200 and see if you can get the photo you want. Comment: I try to shoot at ISO 200 as much as possible - and sometimes lower if very bright out because for photographing birds, I prefer to gamble with motion blur rather than electrical noise from higher ISO. However if the bird is close enough to fill up more than 1/4 of frame, noise will not be a problem because you will not be blowing it up much on the computer. What happens if you set the ISO for 400 and set the exposure time for 1/500 if there is not enough light? The camera will use your set ISO and take the photo at the shutter speed which gives the best exposure. This will be the same result as using “P” mode and setting the same ISO value. Choosing between auto-ISO vs setting a fixed low ISO is definitely a personal preference and you may need to try both ways to see what gives you results that you are happy with. P MODE: In “P” mode, one sets the ISO to a desired value and the shutter speed “floats” - which means it is adjusted automatically by the camera. You might use “P” mode if minimizing the electrical “noise” is a high priority for you. STEPS: 1. Set ISO to 200 - 400 (bright or cloudy) 2. Check exposure time at current ISO setting 3. Shoot photo. Considerations for selecting ISO: Is there enough light to allow ISO 200 (or lower) and still have shutter speeds which will handle the situation? (If there is motion needing to be “stopped” the longest exp time would be something like 1/250. ==> How to adjust for backgrounds which are too bright (or dim). (show picture of SX50 dial here) Use "12-Oclock" position on main dial to dial in a +{1/3 to 1 to 2 or 3} I automatically dial-in a +1 when I am about to photograph a bird against a bright sky or swimming on water which is reflecting a bright sky. I don't even bother to take a photo in those conditions until I have set the +1 (or +2) exposure compensation). Advantage with “P” mode: High ISO noise is avoided by setting low ISO initially. Potential disadvantages to “P” mode: Overly bright (or dim) backgrounds must be handled with an additional step of dialing in some “exposure compensation” (+1 or +2 (or -1 etc)) to brighten the bird/subject of interest. Shooting at fixed low ISO can easily lead to longer exposure times. Always check the shutter speed when pressing the shutter half-way down, to make sure it is fast enough to deal with the degree of motion/activity in your subject.